Andreas Guitar Universe Logo
Home  >  Small Amplified Speaker
Disclosure
This website is a participant in the Amazon Services LLC Associates Program. We are reader-supported. If you buy something through links on our site, we may earn an affiliate commission at no additional cost to you. This doesn't affect which products are included in our content. It helps us pay to keep this site free to use while providing you with expertly-researched unbiased recommendations.

The Best Small Amplified Speaker

Handpicked
Quality-Checked
Generated From 25K+ Reviews!

Buyer's Guide

Tips on Setting Up a Small Amplified Speaker System

There are four common ways of adjusting volume controls on small amplified speakers: by touch, via an audio interface, by ear or by using a digital distortion detector. Setting up by ear with live music is difficult and will often result in inaccurate settings. However, if the music has been recorded using a quality control application such as Windows Live Music Control, then it is relatively easy to set up. If it has been downloaded from the internet, then the user has only to follow certain simple steps.

Buyer Guide For most home theater enthusiasts, setting up a small amplified speaker and amplifier is a snap. For the amateur enthusiast, setting up the amplifier and speakers should be left to someone who is knowledgeable about home theater electronics. The majority of DVD players have built-in amplifiers and speakers. However, if your DVD player does not have one, then you can opt for an aftermarket amplifier.

When setting up small amplified speaker systems, you should always connect the speaker leads to the rear of the amplifier. You should use the speaker cable that came with your DVD player. If you did not receive a speaker cable with your player, you can buy small amplified speaker wire online. This enables you to experiment with different configurations without having to replace the entire speaker system.

Connect the stereo audio lead from the amplifier to the female header on the front of the small amplified speaker. In most cases, the female header will also contain the wiring for the equalizer and volume control. Connect the male stereo audio lead from the amplifier to the female header on the back of the speaker. In most cases, the male header will also contain the wiring for the equalizer and volume control.

To get the best performance out of your small amplified speaker or subwoofer, you should get the right power source. You can select from small audio amp power units that include the signal output trimming control. In addition, there are small amplifiers that come with input/output options for ground and speaker level signals. In order to get the best performance from your amplifier, make sure it has accurate voltage control. The wattage and Ohm rating should be appropriate for the unit.

Connect the speaker wire from the audio amplifier to the speaker board through the female header. The female header connects to the speaker board through a wiring loom. This enables you to install the speaker without soldering the wires together. If you need some assistance with this procedure, you can visit your local electronic store or consult the instructions included in your operating manual.

With your amplifier set up, connect the speaker to the amplifier's power lead. Use the RCA cables to connect the speaker to the front panel of your DVD player or stereo audio source. This allows you to enjoy true surround sound effects.

If you use an amplifier without the ability to change the input signal, you will need an amplifier that offers the option to do so. There are models that offer one-step and two-step gain control. Once you have the ability to vary the input signal, you can use a subwoofer or speaker that has a similar bass capability to boost the sound of your music.

For optimum performance, you should set your speaker at the ideal listening position. The ideal listening position is at ear level when looking straight ahead. You should be able to hear all of the audio channels clearly. Listen to a short sample of the audio played on the DVD player. You will need to listen closely to detect any background noise, which may cause your DVD player to not sound correctly.

When you have your speakers connected and your source selected, it is time to make adjustments to the input signal level. The volume control is usually found on the front panel of the amplifier. The gain controls how much higher the speakers are able to handle the full volume output of the amplifier. You can select a setting that is appropriate for your needs. It is good to experiment with the gain controls until you find a comfortable setting for listening.

Finally, you should connect your small amplified speaker to its amplifier. The connection between the speaker and the amplifier should be done carefully. This process is sometimes referred to as RCA connections. The terminals on the amplifier should be placed in such a way that you can easily reach them. You should try to keep the speaker as far from the power cord or other electrical sources as possible. You should also keep a few rubber or foam grips on hand for when the power cord is stuck in your hand.

menu